Page 1 of 1

Project base to SRT

Posted: Sat Feb 07, 2015 12:32 am
by dawm
Will start adding crap here for my 04 base to SRT swap.

04 Base ATX (w/ no reverse) $800
03 GT Cruiser motor (w/ ALT, A/C Compressor, Jack Shaft) $180
02 PT Cruiser MTX front knuckles
02 R/T ABS brake lines/sensors
04 SRT front and rear brake calipers
04 SRT brake booster & master cyl. & ABS controller
02 R/T ABS controller w/ traction control
03 SRT front and rear seats (same seata I had in my 02 R/T) $400
04 SRT interior/rear body harness w/ Kicker Livin Loud package
04 SRT dash harness
04 SRT engine bay harness
04 SRT engine harness & sensors
04 SRT A/C plumbing
04 SRT stock airbox and plumbing
04 SRT Kicker Livin Loud trunk subwoofer enclosure & amp (woofer damaged in shipping) $25
05 SRT Kicker Livin Loud subwoofer speaker (BNIB) $90
04 SRT Stage 1 PCM w/ SKIM, RKE and FOBs
04 SRT Steering wheel & steering column
04 SRT Power steering pump w/ lines $50
04 SRT Power steering rack $50
04 SRT Stock fuel line (hardline)
04 SRT K-frame (w/ sway bar & control arms) $40
04 SRT Rear spindle x2 (w/ full brake setup) $100

... More to add ...

Clevite H rod bearings (Calico coated)
Clevite H main bearings
Eagle Rods w/ ARP rod bolts $200
JE 8.5:1 .020 Pistons (taken from the 1g build) $0
JE Piston rings
Machining (bored .020 over, burned, blasted, crank polished, water pump castings removed) $350

... More to add ...

03 R/T front & rear bumpers (silver) $100
02 R/T front bumper (white) $80 @@ need to pick up from Riddler
02 R/T side skirts & clips (black) $20~
04 SRT rear bumper (orange) $80
04 SRT front bumper (eblue, bad shape) $200
04 SRT side skirts (eblue, partial set) ^ included above
04 SRT door accents (eblue, partial set) ^ included above
04 SRT hood (black, need scoop insert) $200
04 SRT front bumper (black) $100
04 SRT side skirts (black) $100

Re: Project base to SRT

Posted: Sat Feb 07, 2015 12:33 am
by dawm
Took the GT/SRT engine to the machine shop for boring, decking, burn blast, crank polish and rings filed. Putting the JE .020 over 8.5:1 pistons (from my 1g project) and eagle rods in this motor. All the turbo bits including the head from the 1g are also going on this motor.

Re: Project base to SRT

Posted: Sat Feb 07, 2015 10:22 am
by Eric12775
Everyone!!, remember this date because 7 years from now it wont be finished

Re: Project base to SRT

Posted: Sun Mar 08, 2015 9:40 pm
by dawm
Dumping some pictures I've posted on facebook, first two are from the machine shop, further down is when I finally had it and then it was painted Torque'n'teal and expansion plugs installed. Also picked up a blue SRT front bumper, partial skirts and door pieces, then bought another black SRT front bumper and skirts, srt kframe w/ sway bar & control arms, rear brake setup w/ spindles (only bought the spindles but seller just cut the whole thing off the car and gave me the entire setup), srt fuel line, a noname 3" core BFMIC.

Image

Image

Image

Image

Image

Image

Image

Re: Project base to SRT

Posted: Wed Apr 01, 2015 3:20 pm
by dawm
Image
Image
Image
Image